Installation Guide
Wallpaper Installation Instructions
MuralsAll wallpapers are prepared with different installation methods depending on the selected material type. For the best result, review the guide that matches your product material before you begin. Make sure the wall surface is clean, dry, smooth and free from dust.
Vinyl and Non-Woven Panel Wallpaper
Panels are applied side by side, edge to edge. Overlapping is not required.
Wallpaper Paste Preparation
Shows the correct water ratio and mixing method for paste-required wallpapers.
Peel and Stick Self-Adhesive Wallpaper
No paste is needed. Peel the backing paper gradually and apply with controlled pressure.
Wallpaper Mural Installation
Vinyl and Non-Woven Material
Edge-to-edge installation guide for panel wallpaper murals
Required Tools
Paste
Plastic Spatula
Before You Start
- Check your wallpaper mural for possible printing or cutting issues before installation.
- Measure the wall and decide your starting point in advance.
- Apply paste to each panel one by one. Do not paste all panels at the same time.
Installation Steps
Check Panel Widths
Determine where the first panel will start and end on the wall.
Draw a Vertical Reference Line
Draw a straight vertical reference line at the ending point of the first panel.
Prepare and Apply the Paste
Prepare the paste according to the product instructions. Paste panels one by one; do not paste them all at once.
Place the First Panel
Start from the top and place the first panel in alignment. Leave extra margin at the ceiling and floor; do not trim immediately.
Join the Second Panel Edge to Edge
NEW: EDGE-TO-EDGE SEAMIn the new production method, seams are not overlapped. Align panels side by side, edge to edge, and check the pattern continuity.
Install the Remaining Panels
Install all panels from left to right using the same method. Check the design match at every seam.
Smooth and Remove Air
Use a plastic squeegee to press from the center toward the edges and remove air bubbles.
Final Trimming
Carefully trim the excess wallpaper around the edges, ceiling and floor with a sharp utility knife.
Wallpaper Paste Preparation
Correct mixing and application instructions for wallpapers that require paste
Required Materials
Preparation Steps
Check the Paste Quantity
One paste pack is sufficient for approximately 5 m². Your box includes the required number of paste packs according to your order size.
Measure the Water
Mix 1 paste pack with 1.5 liters of water. If you received 2 packs, use 3 liters of water.
Add the Paste Slowly
Pour the paste powder slowly into the water while stirring continuously. Do not allow lumps to form.
Mix Until It Thickens
Continue mixing for 3–4 minutes. The paste is ready to use when it thickens to a smooth, pudding-like consistency.
Start Installation
Apply the paste to the back of the wallpaper or to the wall, depending on the product instructions, and begin installation.
Digital Printed Wallpaper
Peel and Stick Self-Adhesive Material
Practical installation guide for wallpapers that do not require extra paste
Required Tools
Knife
Plastic Spatula
Installation Steps
Prepare the Surface
The surface must be clean, dry, smooth and free from oil. Remove dust, dirt, moisture and silicone residue. Adhesion may be weaker on textured or rough surfaces.
Align and Measure
Align the wallpaper according to the application area. If needed, measure and trim excess areas with scissors or a utility knife.
Peel the Backing Paper
Start from the top and slowly peel the backing paper. Do not remove it all at once; continue peeling gradually during installation.
Apply the Wallpaper
Stick the wallpaper onto the surface and smooth it with a squeegee from the center toward the edges. Push air bubbles outward.
Trim the Edges
Carefully trim excess material around walls, ceiling, floor and corners with a sharp utility knife.
Final Check
Inspect the entire surface for bubbles or lifting edges. If needed, press again with the squeegee.
Important Notes
- Recommended application temperature is 10–30 °C.
- Wait at least 3–4 weeks before applying on newly painted walls.
- Not recommended for textured, rough or silicone-coated surfaces.
- For indoor use only; avoid long-term contact with water.